The sequencer allows you to connect up to eight outputs and control them in sequential patterns. Sequences that would take as long as 4 days to program without littleBits will only take you seconds!
- Automatically cycle through the entire sequence
- Control the speed of the sequence using dimmers or sensors
- Run the sequence four ways: forwards, backwards, pendulum, or random
- Swap automation for full control and step through each part of the sequence using a button, sound trigger, or any other high signal input
Check out littleBits Sequencer Tips + Tricks!
There are two clock modes that control when the module transitions from sequence step to sequence step. In “step” mode the sequence transitions to a new sequence step on input low-to-high transitions. In this mode, the clock output is high when the input is above 2.5V, and the clock output is low when the input is below 2.5V.
In “speed” mode the sequence transitions to a new sequence step at a fixed frequency. The step frequency is proportional to the voltage at the input. At 0V input, the frequency is 0Hz (the sequencer does not step). At 5 volts the step frequency is approximately 80Hz. In this mode, the clock output is a square waveform at the step frequency The four sequence modes control the order in which the 8 sequenced outputs are activated. At any given time, there is exactly one of the 8 sequenced outputs set to 5V. All other outputs are set to 0V.
“Forward” mode sets output 1 to 5V, then on the next step output 2 is set to 5V, and so on. After activating each output in turn, the sequence then continuously repeats, starting at output 1.
“Backwards” mode is the same as “forward” mode, except that the sequence steps from output 8 to output 1 and is set to 5V at each step.
“Pendulum” mode sets output 1 to 5V, then on the next step output 2 is set to 5V, and so on. Upon reaching output 8, the sequence reverses and steps down from 7 to 1.
“Random” mode sets a randomly selected output to 5V at each step.
UNDER THE HOOD
The input signal is buffered by an opamp (U1), then passed through a single pole RC low pass filter, then a 2-pole active low pass filter (U3). The combined filters band limit the signal to 160Hz with an 18dB per octave filter slope. This signal is split into two paths. One path leads to the Analog-to-Digital Converter (ADC) of an Atmel ATMEGA168 microcontroller (U2). The other path leads to a General Purpose Input-Output (GPIO) pin on the same microcontroller. The path to the ADC is used in “speed” mode because in speed mode, we need to precisely measure the input voltage, and the ADC is precise. The path to the GPIO pin is used in “step” mode, because we need to quickly measure the timing of an input low-to-high transition, and the GPIO pin responds very quickly to transitions. Depending on the clock mode, microcontroller converts the measured input values into either the sequencer step speed in “speed” mode, or simply goes to the next sequencer step when it detects a low-to-high transition in “step” mode. These values are translated into signals that control the pins of the microcontroller connected to the various outputs.
Have questions? Mingle with the pros on littleBits forum!
- Dimensions (mm): 1.13(H) x 0.06(W) x 4.63(D)
- Product Weight: 0.02 lbs (0.01 kg)
- Recommended Age: 8+
- SKU: 650-0008
- UPC: 810876020299
- Extra Materials Circuit Diagram - PDF
This product is listed in:
Documentation and Resources:
- What is the better tech, innoBits or littleBits?
We get a lot of interest from parents and educators surrounding littleBits and innobits. Especially the difference between the two products. Both are magnetically connected electronic building blocks. Both products empower people to invent and create...
- The One Wand to rule them all!
Wands are cool, right? That's what Trinity, Adele, and April were thinking of our recent littleBits Workshop, down at the Core Electronics Knowledge Factory. Their inspiration for this project came straight from the films, in particular, the magic wands that Harry and co use throughout the Saga. They went a bit above a typical wand though, using a pressure sensor alongside a fan, buzzer, and bar graph to make their wand light up...
- littleBits Death Eater Skull!
Remote Controls are magical enough to recreate this awesome Death Eater Skull. You can switch it on from across the room and make it glow an evil green! Jake and Nathan built this invention at a littleBits Workshop down at the Core Electronics Knowledge Factory. At first, they tweaked an RGB LED Bit to be the perfect green and after some additions and problem solving they ended up with this remotely controlled Skull lamp. Just a...
Exact shipping can be calculated on the view cart page (no login required).
We deliver Australia-wide with these options:
- $3 for Small Items (3-7 days, not tracked, only available on selected small items)
- $6.95 for Standard Post (2-4 days, tracked)
- $8.95 for Express Post (Overnight for Australia Post Next Day Network, tracked)
- Pickup - Free! Only available to customers who live in the Newcastle region (only after we email you to notify your order is ready)
International Orders - the following rates are for New Zealand and will vary for other countries:
- $11.49 for Pack and Track (3+ days, tracked)
- $16.50 for Express International (2-5 days, tracked)
If you order lots of gear, the postage amount might increment based on the weight of your order.
Our physical address (here's a PDF which includes other key business details):
Unit 18, 132 Garden Grove Parade
Take a look at our customer service page if you have other questions such as "do we do purchase orders" (yes!) or "are prices GST inclusive" (yes they are!). We're here to help - get in touch with us to talk shop.